Powder coating for metal fabricators gives welded steel and aluminum work a tough, even finish without slowing production. At Koojo Custom Powder Coating, our Milton team finishes welded assemblies, frames and parts for fabrication and welding shops across the GTA. Since 2012, we have finished more than 10,000 items, and typical orders carry a 48-hour turnaround. Our powder coating for metal fabricators covers everything from single welded pieces to repeat production runs. If you need a welding shop finishing partner, call (905) 876-7060, Monday to Friday, 7 AM to 5 PM, or request a quote for powder coating for welding shops.
Since 2012 | 10,000+ Items | 48 Hr Turnaround | 5.0 ★ Google Rating
Coating Challenges for Metal Fabricators and Welding Shops
The main coating challenges for fabricators are weld seams, spatter, mixed metal thickness, sharp edges and tight deadlines. Each can cause thin spots, pinholes or rework without planning. Powder coating for metal fabricators works best when the weld is treated as part of the finish.
Welds are rough and often porous, and they heat differently from the sheet beside them. Weld spatter leaves bumps that show through the coating. Weld porosity traps air, which oven heat can push out as outgassing and leave blisters. Sharp edges pull the coating thin, so edge coverage needs attention on cut plate and tube ends. A heavy base plate welded to thin sheet also heats unevenly in the oven. Add the deadlines your own customers set, and finishing often becomes the bottleneck. Good powder coating for fabricators removes these risks before parts reach the oven, which keeps fabricated metal parts moving. Fabricator powder coating also has to cope with mixed shapes, sizes and metals, often in the same batch.
Choosing powder coating for metal fabricators with a documented prep routine protects your reputation as well as the part, because a failed finish comes back to the shop that built the frame.
Parts and Metals We Coat for Fabricators
We apply powder coating for metal fabricators to steel and aluminum parts from fabrication and welding shops, including weldments, welded frames, tube steel frames, brackets and plates, enclosures and cabinets, and sheet metal parts. Our capabilities page lists 6,000 lb capacity, so heavy assemblies are worth a quote.
- Weldments and welded frames: base frames, stands and carriers built from tube, angle and plate.
- Tube steel frames: rectangular and round tube builds with closed ends and tight corners.
- Brackets and plates: cut and formed pieces whose edges need careful coverage.
- Enclosures and cabinets: welded sheet metal housings, panels and covers.
- Steel racks and fixtures: racks, jigs and holders used on your own shop floor.
Our sheet metal powder coating and aluminum fabrication powder coating each follow a prep and cure plan matched to the metal. For steel fabrication powder coating, we check for oil, scale and weld residue first. Share drawings or photos with your request, and we will confirm the prep plan for your custom metal fabrication work. Powder coating for welded parts also depends on how each piece is hung, so we choose hanging points that leave no marks on show surfaces. That planning keeps powder coating for metal fabrication consistent across mixed jobs, and it is what helps the finish last.
Finishes and Specs for Fabricated Parts
Powder coating for metal fabricators comes in gloss, satin, matte and textured finishes. We confirm the powder, colour and film thickness at quote so the coating suits the part and its end use, and we can match a RAL code or supplied sample.
- Finish choice: gloss for display work, satin or matte for lower glare, and textured finishes that hide small marks near welds.
- Film thickness: we agree a target at quote, because even a typical 2 to 4 mil film can affect threaded holes and mating faces.
- RAL colour match: send a code or sample for repeat orders so later batches look like the first.
- Powder type: we confirm whether epoxy, polyester or hybrid powder suits indoor or outdoor use before coating.
- Durability: in powder coating for metal fabricators, heat-cured thermoset powder forms one continuous layer, a corrosion-resistant finish and chip-resistant finish for parts that face weather, handling and wear.
- Standards: our quality checks reference ASTM D3359 for adhesion, ASTM D7091 for coating thickness readings and ASTM B117 for salt spray resistance.
Our certification comes through the Absolute Bureau of Certification, and we can supply test reports when your own customer asks for them. Welded corners and cut edges are where thin spots tend to form, so we check them closely in powder coating for metal fabricators. Salt spray hours compare coatings under controlled conditions rather than predict field life, so we explain how to read a result for your parts. Our approach to powder coating for fabrication shops uses these same documented checks. See our certification page for details.
How We Work With Fabrication Shops
Powder coating for metal fabricators follows five stages at Koojo: intake and inspection, cleaning and pretreatment, masking and powder application, oven curing, and final inspection. We document each stage so repeat runs follow the same steps, and typical orders follow a 48-hour turnaround.
- Step 1 – Intake and Inspection: We inspect each part for spatter, oil, rust, old coatings and damage, and we agree the finish and timing with you. Photos sent before drop-off help us flag issues early. Planning how a welded frame will hang comes first, because every surface must be reachable.
- Step 2 – Cleaning and Pretreatment: Parts are cleaned and pretreated chemically so the powder can bond to bare metal. Early coating failures often trace back to weak cleaning, so powder coating for welded parts is never treated as a spray-only job. Residue collects along weld seams, so those areas get close attention.
- Step 3 – Masking and Powder Application: We plug threaded holes and cover mating faces first. The powder is then sprayed electrostatically onto the grounded part, which draws it around tube walls and corners. Deep recesses can limit coverage, so racking and spray angles are planned in advance.
- Step 4 – Oven Curing: Parts cure in the oven at 180 to 200 °C. Heavy base plates take longer to reach temperature than thin sheet, so fabricator powder coating schedules each assembly by its mass.
- Step 5 – Final Inspection and Handoff: The cured finish is checked for coverage, adhesion and appearance. We log the colour code and powder so a later run can match, and parts are received Monday to Friday, 7 AM to 5 PM.
For shops with recurring work, this routine supports batch consistency from one run to the next. If your shop sends parts weekly, say so at quote and we will plan around it. We confirm pickup and delivery details at quote, which makes powder coating for fabrication shops easier to schedule. We aim to be an extension of your own shop, because powder coating for metal fabricators should add predictability, not another variable.
Services Fabricators Use Most
Powder coating for metal fabricators usually combines three services: our industrial powder coating as the base, plus preparation, rust removal or recurring batch runs as the work requires. Each is quoted on its own details, so you choose only the steps your parts need.
Use powder coating surface preparation when welds, oil or residue need cleaning and pretreatment before the powder goes on. Choose sandblasting services when parts carry heavy rust or scale. For recurring production work, commercial powder coating keeps jobs on a steady schedule. Together, these steps give powder coating for fabricators a clean start and a consistent finish.
A short call helps too. Tell us your metal, size, quantity and finish, and we will recommend the steps for your parts, whether that is a weekly batch or a single urgent piece.
Recent Project: Automation Line Frame
Our automation line frame shows how we handle fabricator powder coating for work that has to fit, bolt up and last on a production floor. Its write-up covers the part, metal, size, powder, colour code and turnaround, with before and after images.
Read the automation line frame case study for the full record. The record shows what was coated, how it was prepared and how it came out, which is the proof a fabricator needs before trusting a new finisher. Expect the same documented routine on your powder coating for metal fabricators order.
Have drawings ready? Send them with photos, quantities and your finish choice for powder coating for metal fabricators using our quote form. You can also call (905) 876-7060 between 7 AM and 5 PM, Monday to Friday, or contact us to arrange a visit to 10874 Steeles Ave E, Milton.
Frequently asked questions
Should we grind welds before sending parts?
Grind off heavy spatter and sharp burrs where you can, because they show through the finish. Smooth, sealed welds also cure better, which makes powder coating for metal fabricators more predictable. Tell us what you have already done, and our team inspects the rest at intake.
Why do some welds bubble after curing?
Air or residue trapped in a porous weld can escape as heat rises, which leaves a blister or pinhole. Sealing welds before coating lowers the risk. Mention porous sections at quote, and we plan the cure around them, which is routine in powder coating for fabrication shops.
Can you coat parts with tight tolerances?
Yes. Coating thickness affects fit, so flag threaded holes, bores and fit-critical parts when you request a quote. Powder coating for metal fabrication can work with tight fits when we know where they are, so we mask those areas before coating.
Do you take subcontract work from other shops?
Yes. We take subcontract powder coating from fabrication and welding shops, and we record the colour code and powder on each job. Ask about outsourced powder coating for recurring work at quote.
Can steel and aluminum parts go in the same order?
Yes, mixed metals can be quoted together, but each metal gets its own prep and cure plan. List the metal for every part when you request a quote.
What should we send with a quote request?
Send photos, dimensions, quantities, the metal and your finish choice. Drawings and part counts help us plan racking. With those details, powder coating for welding shops can be quoted and scheduled faster, and we flag any prep concerns before parts arrive.